How to Make a Cutting Board
Release time：2023-07-15 02:54:49 oRead0
Method 1
Method 1 of 3:
Collecting Your Supplies
-
1
Buy three thick planks of wood to build your board. You can use any wood you want, in any dimensions, but you should have at least 1" thickness. For this tutorial, you will be using:
- 1 Walnut board 4″ x 20″ x 1″
- 1 Maple Board 4″ x 20″ x 1″
- 1 Cherry Board 4″ x 20″ x 1″
-
2
Round up your construction and safety supplies. This is a simple tutorial, but it does require a fair amount of supplies to do correctly. You should have:
- Wood glue
- Safety gloves, goggles, and earmuffs
- Tape measure
- Pencil
- Earmuffs
- 2-3 sets of clamps.
-
3
Ensure you have the correct woodworking machines. You will need to be comfortable with the following machinery and know how to use it safely.
- Orbital sander
- Table saw
- Miter saw
- Planer
-
4
Measure and cut your board to 1/2 or so longer than your final length. The final length of the board comes down to you -- this tutorial will be aiming for a 12" x 16" board. No matter your final length, leave an extra 1/2 or so now -- you'll clean the edge to your exact specifications later.
- No matter what your length, make sure you cut all the boards to the same length.
- You can use either the miter saw or the table saw.
- Make sure you cut off any rough edges.
-
1
Mark the "width" of each strip in your cutting board with a pencil. Again, the exact width is up to you, but 3/4" is a good, workable thickness. Measure out each strip of wood on the walnut, maple, and cherry boards with your pencil.
- You want the strips to run lengthwise along each board -- you'll then alternate strips from each type of wood to build the final cutting board.
-
2
Use the table saw to cut each strip of wood. Working slowly, cut along your pencil lines. You should end up with three sets of perfectly even strips of wood. They look like square posts.
- The number of strips you end up with will depend on the starting width of your wood.
- You can play with or adapt this formula -- cutting different widths to get a variable striping on your final board -- if you want.
- 3 Line up all of the strips of wood, placing them in the pattern you like. The easiest style is to alternate -- cherry, maple, walnut, cherry, maple, walnut, cherry... etc. Rotate the strips so that the nicest side is facing up, and place the wood into a "dry cut" of the final cutting board.
- 4 Rotate each strip clockwise so that the side faces up. You'll be using wood glue to adhere the wood strips to each other, so turn each piece over so that the side you'll be gluing faces upward.
- 5 Apply wood glue liberally to each strip of wood. Use your fingers or a brush to apply glue to one side of every strip of wood. You want glue covering the entire side. Don't worry about dripping or excess glue now -- you'll clean it up later.
- 6 Press all of the wood evenly together. Rotate the wood back counter-clockwise so that the glue sides are between each piece of wood. Line them up and press them together, making sure they don't buckle or slide.
- 7 Attach clamps on either side of the board so that the wood is pressed closed together. This is necessary to help the wood glue dry appropriately. Make sure, as you apply the clamps, that the wood stays level. No pieces should "buckle" or push upwards. Ensure that the bottom or top is roughly even as well.
-
8
Lift the clamped set of strips of the work surface, drying the wood glue so that it doesn't stick to the table. Lift the cutting board vertical and let it dry for the recommended time on the wood glue bottle.
- This should take 1-3 hours, but check the bottle for specifics.
- 1 Remove the clamps and use a chisel to remove large chunks of glue. Take the clamps off once the wood glue dries. If there are any big chunks of glue on the board, lightly chisel them off now.
-
2
Run the board through your planer. This gives it an even, perfect surface. You don't need to take much off -- only a few millimeters. Run both sides through for a perfectly smooth board.
- Taking off roughly a 1/8 on an inch from each side will generally get out any issues or imperfections.
- 3 Use your table saw or miter saw to cut your edges to perfect size. Now that all the strips are attached it is easy to get the board to the perfect size. Set your saw to your final length, here 16", and cut the ends of the board to your final length.
- 4 Use your orbital sander to give the board a smooth polish. After the planer, you shouldn't need to do a lot of sanding. Use 220 grit paper to smooth the board, round the edges, and take out any roughness created by the saw.
-
5
Finish the board with some food-grade mineral oil. This puts a protective coating on the board and makes it easier to clean and work with. Use a damp rag to wipe off the board, then dry it thoroughly. Working in small circles, apply the food-grade mineral oil to the board, using a rag to apply a thin coating across the entire board. Let it dry and your cutting board is ready to use.
- The final board should have a light shine on it. Reapply the mineral oil if it seems rough, woody, or unfinished in places.
- Linseed oil and beeswax are two common food-grade oils.